Printer Parts are replacement parts for SMT Solder Paste Printer machines. These parts include wear and tear parts like rubber squeegees, metal blades, and other common printing machine parts. We also supply other Solder Paste Printer machine parts for all brands and models of SMT Solder We distribute original-brand new spare parts and high SMT Printer parts. For further information and inquiries, you can contact us or visit our official website. Printer Spare Parts,Printer Parts,SMT Squeegee,SMT Squeegee Blade,Squeegee Holder,Squeegee Holder Screen Printing ShenZhen KDW Electronics Co.,Ltd , https://www.smtsplicetape.com
The development of China's explosion-proof ball machine industry is based on application, from public management and service market, to industry application market, to individual family market, and gradually develops into mature market segments, which drives the improvement of various technical services and processes. Improvements, the application of the explosion-proof ball machine market will also develop. This will also push the explosion-proof dome to a new level.
There are three types of ball machines commonly available on the market: fixed type, rotatable type, and PTZ type. Depending on the type, the functions are different, and the user has more room to choose. You can choose the products that meet your needs according to different application environments.
The explosion-proof ball machine is the front-end image acquisition device often used in video surveillance systems. Because the explosion-proof ball machine integrates multiple function modules such as dome control, array infrared lamp power supply and control, integrated zoom movement control, and intelligent The function is also becoming more and more abundant, and it is an intelligent system. Therefore, the following seven points should be kept in mind when installing the explosion-proof dome, so that the installation and operation of the explosion-proof dome can be done quickly and easily.
First, after getting the explosion-proof dome, remember that the whole process should be handled with care. Only the explosion-proof dome that cares for you will “return†you, which is lower failure rate and longer service life.
Second, many people like to use the hand to go to the tail line of the ball-lifting machine during the installation process. The core wire of the explosion-proof ball machine is connected to the interface of the conductive slip ring, and the core wire is directly lifted, which is prone to bad interface. A good way to use zui is to hold it up with both hands.
Third, during the installation process, the power cord should be connected to the explosion-proof dome, and the power adapter cable should not be extended, and the centralized power supply mode should not be used. If centralized power supply is used, the voltage of the explosion-proof ball machine that arrives in the room may be insufficient. Especially in thunderstorms, the resistance resistance is increased. The insufficient power supply may cause the main board to burn out and thus cannot be controlled.
4. When wiring, remember to distinguish the RS485 protocol communication line and power line. If RS485 is connected to the power supply, the explosion-proof ball machine may burn on the spot, so you should carefully see the logo and protect the relevant logo, which is convenient for yourself. Maintenance in the future.
5. When installing, the 220V power cord should be connected to the dome. Do not use low-voltage remote power supply. Do not extend the power adapter cable of the dome to avoid voltage shortage or power interference.
Sixth, the explosion-proof ball machine is not the same as the outdoor environment. If it is installed outdoors, it must be rigorously waterproofed. You might say that the explosion-proof dome is not waterproof? The ball machine itself is waterproof, but it must always be connected to the outside when installing. There is always a joint. If the joint position, the combination method is improperly designed, or the seal is not good, it may cause water inflow, especially by lifting installation or self-made. When the wall mount is installed, we have to deal with the waterproof problem seriously.
7. It is important to choose the right power source. Why? If the power supply is too small and the rated power is not working, the capacitance of the main control board will continue to discharge, which will damage the components and shorten the life of the explosion-proof ball machine. At the same time, the infrared power will not meet the requirements; If the power is too large, it will cause waste first. Secondly, the power supply volume and weight will be large, which will cause inconvenience to the installation.