There are no problems with the components of the cooling system. However, the cooling effect of the engine is still poor, and high-temperature pot boiling problems often occur. It is recommended that the card-friends carry out the engine cooling system modification and replace the intelligent cooling system of the electronic fan cooling engine. Electronic fan heat dissipation was first applied to cars. As the technology matures, urban buses have also rapidly gained popularity. At present, there are many pure electric vehicle logistics applications in the truck area where electronic fan cooling is used and the cooling effect is good. Fans become smaller fans, not cooling? Truck Engine Intelligent Cooling System ATS is an electronic fan cooling engine cooling system developed and designed by the company. Truck ATS systems use modular electronic fans instead of the usual belt or clutch fan. According to Product Manager Liu Product Department, the benefits of electronic fan cooling is to achieve electronic control, completely out of dependence on engine speed, fan speed and heat only with the engine's cooling needs, but not with the engine operating state. Simply put, when the engine is running at low speed, the electronic fan can still run at high speed. The speed of the electronic fan is intelligently controlled by the ECU that connects the inlet and outlet sensors of the engine water tank and is proportional to the engine cooling requirement. In addition, the smaller the diameter of the electronic fan, the corresponding reduction in noise, improving the overall comfort of the vehicle. Of course, although the diameter of the electronic fan becomes smaller, the amount of heat generated can not be reduced. The modular electronic fan can completely provide the cooling air volume that a large-diameter cooling fan can generate. “Electric fans not only can meet the engine cooling requirements, but also have better cooling effect. The introduction of intelligent truck cooling system can not only effectively solve the truck engine high temperature problems, but also can greatly improve the engine fuel economy, improve engine operating efficiency, and prolong life "The manager of Liu Li Product Department finally said:" With the promotion and application of intelligent cooling technology for electronic fans, the intelligent cooling system represented by the ATS system will increasingly appear on trucks. We believe that This is an inevitable technological innovation trend." Electronic fan cooling application in truck market The electronic fan cooling engine intelligent cooling system has passed various tests to enter the small batch application stage. According to the introduction of the Market Research Department, Cardmates can experience the engine intelligent cooling system ATS in two ways: First, the engine cooling system is modified. In 2016, CHILI Technology held a free test-fitting event. As long as the application is approved, the card-friends can exchange the engine intelligent cooling system ATS for free, and get full after-sales service. Due to the limited number of places, many card members did not get their wish. To this end, Reliance Technology held an “ATS Remodeling Group Purchase†event in July and August 2017. The card-friends only need to find a large-scale repair shop to cooperate and provide 50% discount for refitting applications for 10 vehicles in the same area. Offers. The second is the purchase of new cars. Qili Technology has strategic cooperation with a number of truck OEMs. In future models, new production trucks will be equipped with an ATS system for electronic fan cooling. Reliance Technology is a high-tech auto parts company dedicated to the energy saving and optimization of power systems. The core product intelligent cooling system ATS was selected by the National Development and Reform Commission's “National Promotion Catalog for Key Energy Technology†(2012). The technical upgrading of engine cooling system is an inevitable trend for the development of commercial vehicle cooling systems. Under the vigorous promotion of Haoli Technology, the passenger car has completed the upgrading of the engine cooling system technology. Electronic fan cooling has become very common, and it is believed that the cooling technology upgrade of the truck will also Must be! QL Cnc Processing Center: A flexible and secure path to the future
Our CNC processing center includes Cnc Punching, Cnc Bending , Cnc Laser Cutting, CNC welding, CNC processing center and so on.
CNC Processing Center Cnc Processing Center,Cnc Punching,Cnc Bending,Cnc Laser Cutting Parts QL Sheet Metals Co.,Ltd , http://www.ql-metals.com
Truck Engine Intelligent Cooling System ATS is an electronic fan cooling engine cooling system developed and newly designed by the company. 
Electronic fan cooling engine intelligent cooling system has passed various tests to enter the stage of small batch applications
The QL CNC Processing Center is designed for surface parts from sheet metals for the highest quality and flexibility requirements.
CNC processing center forms: by samples or drawings, processing: labor and materials processing.
From south to north, from east to west, China has entered a full range of high-temperature weather, and local high-temperature warnings sounded from time to time. On such a hot day, the fans can no longer meet the needs of the summer heat. Only air conditioning can solve the problem. In summer, people are afraid of heat and the car is more afraid of heat. At this time, if the engine cooling system is not to force, it is hard to imagine. However, there are some car friends who always have high temperatures. What should I do?